就直線光軸的精度來講，它其實也就是會直接的就取決與軸的位置以及其用途。就這個方面來講，我們其實也就是要傳動軸頸上的同軸度，就這個方面來講，直線光軸其實也就是會對傳動的精度直接的就造成影響，就另外一個方面，它其實也就是會有噪聲的出現。下面導軌絲杠廠家為您分析更多內容：

In terms of the accuracy of the linear optical axis, it actually depends directly on the position of the axis and its purpose. In this regard, we actually need to ensure the coaxiality of the transmission shaft neck. In this regard, the linear optical axis actually has a direct impact on the accuracy of the transmission. On the other hand, it actually causes noise. The manufacturer of the guide rail screw will analyze more content for you below:

就另外一個方面來講，對于直線光軸的要求與生產的類型等一系列的方面來直接的就選擇相應形式的一個毛胚形式。就另外一個方面來講，它其實也就是會對直徑的差距不是特別大，就另外一個方面來講，我們其實也就是可以用棒料，如果他們的差距比較大的話，我們其實也就是可以直接的用鍛件。

On the other hand, for a series of aspects such as the requirements for linear optical axes and the type of production, a corresponding form of hair embryo is directly selected. On the other hand, it actually means that the difference in diameter is not particularly large. On the other hand, we can actually use bar materials. If their difference is relatively large, we can actually use forgings directly.

再者，我們其實也就是要注意，就其把直線光軸直接的就裝入到軸承座的時候，應該直接的就使用輔助工具，就另外一個方面來講，我們其實也就是要注意避免其直接敲擊它的端面或者是密封圈，應該直接的就使用軸承均勻進行導入，接著，其實也就是要用緩沖板，然后也就是要借助輕輕地敲擊進行裝入。

Furthermore, we actually need to pay attention to the use of auxiliary tools when directly installing the linear optical shaft into the bearing seat. On the other hand, we should also pay attention to avoiding it from directly hitting its end face or sealing ring. We should directly use the bearing to evenly guide in, and then, in fact, use a buffer plate, Then, it is necessary to use gentle tapping to load.

就其把直線光軸直接的就穿入直線軸承，就另外一個方面來講，它其實也就是會把軸與軸承的線連成一直線。如果直線光軸能傾斜的進行插入，就其滾珠來講的話，它其實也就是比較可能會出現脫落的現象，或者是造成其保持架出現變型的現象，以此也就是會對軸承造成一系列的損壞。

On the other hand, it actually connects the shaft and the centerline of the bearing into a straight line by directly threading the straight optical axis into the linear bearing. If the linear optical axis can be tilted for insertion, in terms of its ball bearings, it is actually more likely to fall off or cause deformation of its cage, which will cause a series of damage to the bearings.

們其實也就是要注意，就其外加載荷來講的話，其實也就是應該平均分配在整個直線光軸上，就另外一個方面來講，它其實也就是會直接的就承受了瞬間載荷的試試，應該直接的就可以使用兩個或者是更多的直線光軸軸承。就其軸承如果是不承受旋轉載荷，不然也就會導致一系列的意外事故。更多事項就來我們網站http://m.feicui77.cn咨詢吧！

In fact, we should pay attention that when it comes to the external load, it should be evenly distributed across the entire linear optical axis. On the other hand, it is actually a test that can directly withstand instantaneous loads. It should be possible to use two or more linear optical axis bearings directly. If the bearing does not withstand rotating loads, it will also lead to a series of accidents. For more information, come to our website http://m.feicui77.cn Consult!